- Can you install drip edge over existing drip edge?
- Should drip edge be tight to fascia?
- Should gutters be installed under drip edge?
- Do all roofs need a drip edge?
- Where do you nail drip edge?
- What is the difference between drip edge and rake edge?
- Should drip edge be painted?
- What is a drip edge used for?
- Do you install drip edge before tar paper?
- Can drip edge be installed after shingles?
- How much does it cost to install a drip edge?
Can you install drip edge over existing drip edge?
If the old drip edge is installed behind the gutter or the gutter is screwed through the drip edge and it cannot be removed without removing the gutter it is better to leave it there and install the new drip edge on Top.
We do not remove and reinstall aluminum gutters..
Should drip edge be tight to fascia?
Nail thefurring strip to the fascia board near the fascia top – tight under any extending of roof decking (usually absent); the Drip edge will be installed 1/8″ proud of (away or out from) the furring strip in best practice or may be installed tight against the furring strip (reduces the life of the furring strip by …
Should gutters be installed under drip edge?
Your gutter needs to be a few inches under the edge of your roof. … Drip edge gets installed under the first course of shingles and promotes water to run freely from roof edge down into gutter. Without it, water may run down behind your gutter, down fascia board and siding, leading to potential damage.
Do all roofs need a drip edge?
Without a drip edge, water may end up beneath the shingles and may cause damage to various parts of the home. Though your home may not have originally had a drip edge installed, drip edges are now required by most building codes across North America to protect homes from damage.
Where do you nail drip edge?
Nail the drip edge to the roof deck with minimum 12-gage roofing nails spaced 8 to 10-inches on center and 1-½ to 3-inches from the edge of the sheathing. Adjacent drip edge pieces should be lapped minimum 2 inches. Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch.
What is the difference between drip edge and rake edge?
Drip edge and rake edge are the first parts of the roof system to be installed. … They form a long, narrow piece of metal, which is installed along the perimeter your Roof Deck. Drip edge goes along your eaves trough areas and rake edge goes along your gable ends.
Should drip edge be painted?
Yes you can paint the aluminum drip edge and it hold up very well. Just be sure it is clean and paint it with a good exterior acrylic primer and finish with a exterior acrylic semi-gloss house paint.
What is a drip edge used for?
Drip edge is a metal flashing that is installed at the edges of the roof to help control the flow of water away from the fascia and to protect the underlying roofing components. Drip edge overhangs the sides of the roof and has a small metal flange that is bent away from the fascia.
Do you install drip edge before tar paper?
Installing roof drip edge flashing properly The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.
Can drip edge be installed after shingles?
The drip edge is often replaced when new shingles are installed, but it can be replaced at any time. Asphalt roof shingles can become brittle in cold weather, so wait until a warm (but not hot) day to remove and replace eave stripping.
How much does it cost to install a drip edge?
Drip Edges: $1-$2 per linear foot installed. Inspect and replace drip edges as necessary. Drip edges are added to the roof to direct water into the gutters.